Mittuniversitetet

Production of high-quality syngas from biomass gasification in a dual fluidised bed gasifier (DFBG) has made a significant progress in R&D and Technology demonstration. An S&M scale bio-automotive fuel plant close to the feedstock resources is preferable as biomass feedstock is widely sparse and has relatively low density, low heating value and high moisture content. This requires simple, reliable and cost-effective production of clean and good syngas. Indirect DFBGs, with steam as the gasification agent, produce a syngas of high content H₂ and CO with 12-20 MJ/m_n³ heating value. The Mid Sweden University (MIUN) gasifier, built for research on synthetic fuel production, is a dual fluidised bed gasifier. Reforming of tars and CH₄ (except for methanation application) in the syngas is a major challenge for commercialization of biomass fluidised-bed gasification technology towards automotive fuel production. A good syngas from DFBGs can be obtained by optimised design and operation of the gasifier, by the use of active catalytic bed material and internal reforming. This thesis presents a series of experimental tests with different operation parameters, reforming of tar and CH₄ with catalytic bed material and reforming of tar and CH₄ with catalytic internal reformer.

The first test was carried out to evaluate the optimal operation and performance of the MIUN gasifier. The test provides basic information for temperature control in the combustor and the gasifier by the bed material circulation rate.

 After proven operation and performance of the MIUN gasifier, an experimental study on in-bed material catalytic reforming of tar/CH₄ is performed to evaluate the catalytic effects of the olivine and Fe-impregnated olivine (10%wtFe/olivine Catalyst) bed materials, with reference to non-catalytic silica sand operated in the mode of dual fluidised beds (DFB). A comparative experimental test is then carried out with the same operation condition and bed-materials but when the gasifier was operated in the mode of single bubbling fluidised bed (BFB). The behaviour of catalytic and non-catalytic bed materials differs when they are used in the DFB and the BFB. Fe/olivine and olivine in the BFB mode give lower tar and CH₄ content together with higher H₂+CO concentration, and higher H₂/CO ratio, compared to DFB mode. It is hard to show a clear advantage of Fe/olivine over olivine regarding tar/CH₄ catalytic reforming. 

In order to significantly reduce the tar/CH₄ contents, an internal reformer, referred to as the FreeRef reformer, is developed for in-situ catalytic reforming of tar and CH₄ using Ni-catalyst in an environment of good gas-solids contact at high temperature.  A study on the internal reformer filled with and without Ni-catalytic pellets was carried out by evaluation of the syngas composition and tar/CH₄ content. It can be concluded that the reformer with Ni-catalytic pellets clearly gives a higher H₂ content together with lower CH₄ and tar contents in the syngas than the reformer without Ni-catalytic pellets. The gravimetric tar content decreases from 25 g/m³ down to 5 g/m³ and the CH₄ content from 11% down below 6% in the syngas.

The MIUN gasifier has a unique design suitable for in-bed tar/CH₄ catalytic reforming and continuously internal regeneration of the reactive bed material. The novel design in the MIUN gasifier increases the gasification efficiency, suppresses the tar generation and upgrades the syngas composition. 

The modern concept of “biorefinery” is dominantly based on chemical pulp mills to create more value than cellulose pulp fibres, and energy from the dissolved lignins and hemicelluloses. This concept is characterized by the conversion of biomass into various bio-based products. It includes thermochemical processes such as gasification and fast pyrolysis. In thermo-mechanical pulp (TMP) mills, the feedstock available to the gasification-based biorefinery is significant, including logging residues, bark, fibre material rejects, bio-sludges and other available fuels such as peat, recycled wood and paper products. On the other hand, mechanical pulping processes consume a great amount of electricity, which may account for up to 40% of the total pulp production cost. The huge amount of purchased electricity can be compensated for by self-production of electricity from gasification, or the involved cost can be compensated for by extra revenue from bio-transport fuel production. This work is to study co-production of bio-automotive fuels, bio-power, and steam via gasification of the waste biomass streams in the context of the mechanical pulp industry. Ethanol and substitute natural gas (SNG) are chosen to be the bio-transport fuels in the study. The production processes of biomass-to-ethanol, SNG, together with heat and power, are simulated with Aspen Plus. Based on the model, the techno-economic analysis is made to evaluate the profitability of bio-transport fuel production when the process is integrated into a TMP mill.The mathematical modelling starts from biomass gasification. Dual fluidized bed gasifier (DFBG) is chosen for syngas production. From the model, the yield and composition of the syngas and the contents of tar and char can be calculated. The model has been evaluated against the experimental results measured on a 150

KWth Mid Sweden University (MIUN) DFBG. As a reasonable result, the tar content in the syngas decreases with the gasification temperature and the steam to biomass (S/B) ratio. The biomass moisture content is a key parameter for a DFBG to be operated and maintained at a high gasification temperature. The model suggests that it is difficult to keep the gasification temperature above 850 ℃ when the biomass moisture content is higher than 15.0 wt.%. Thus, a certain amount of biomass or product gas needs to be added in the combustor to provide sufficient heat for biomass devolatilization and steam reforming.For ethanol production, a stand-alone thermo-chemical process is designed and simulated. The techno-economic assessment is made in terms of ethanol yield, synthesis selectivity, carbon and CO conversion efficiencies, and ethanol production cost. The calculated results show that major contributions to the production cost are from biomass feedstock and syngas cleaning. A biomass-to-ethanol plant should be built over 200 MW.In TMP mills, wood and biomass residues are commonly utilized for electricity and steam production through an associated CHP plant. This CHP plant is here designed to be replaced by a biomass-integrated gasification combined cycle (BIGCC) plant or a biomass-to-SNG (BtSNG) plant including an associated heat & power centre. Implementing BIGCC/BtSNG in a mechanical pulp production line might improve the profitability of a TMP mill and also help to commercialize the BIGCC/BtSNG technologies by taking into account of some key issues such as, biomass availability, heat utilization etc.. In this work, the mathematical models of TMP+BIGCC and TMP+BtSNG are respectively built up to study three cases: 1) scaling of the TMP+BtSNG mill (or adding more forest biomass logging residues in the gasifier for TMP+BIGCC); 2) adding the reject fibres in the gasifier; 3) decreasing the TMP SEC by up to 50%.The profitability from the TMP+BtSNG mill is analyzed in comparison with the TMP+BIGCC mill. As a major conclusion, the scale of the TMP+BIGCC/BtSNG mill, the prices of electricity and SNG are three strong factors for the implementation of BIGCC/BtSNG in a TMP mill. A BtSNG plant associated to a TMP mill should be built in a scale above 100 MW in biomass thermal input. Comparing to the case of TMP+BIGCC, the NR and IRR of TMP+BtSNG are much lower. Political instruments to support commercialization of bio-transport fuel are necessary.