miun.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
A Local Positioning System for Loader Cranes Based on Wireless Sensors-A Feasibility Study
Mid Sweden University, Faculty of Science, Technology and Media, Department of Information Technology and Media.
Mid Sweden University, Faculty of Science, Technology and Media, Department of Information Technology and Media.
Cargotec Sweden AB, S-82450 Hudiksvall, Sweden.
2011 (English)In: IEEE Transactions on Instrumentation and Measurement, ISSN 0018-9456, E-ISSN 1557-9662, Vol. 60, no 8, p. 2881-2893Article in journal (Refereed) Published
Abstract [en]

This paper presents a feasibility study that deals with a local positioning system for a loader crane based on battery-powered wireless sensors and consists of two joint angular sensors and one telescopic boom length ranger. The practical challenges associated with using conventional sensors are described in order to provide the motivation behind the choice to use the sensing methods proposed in this paper. A novel method is tested using microelectromechanical system inertial sensors mounted around the crane joints to indirectly measure the joint angles, as well as an ultrasound time-of-flight ranging method to measure the telescopic boom length. The local positioning system's wireless sensor prototype designs are described in detail. Data from the angular sensor experiments conducted on a loader crane and the ultrasound ranging experiments conducted both in the laboratory and on the loader crane are presented and analyzed. The preliminary results from these experiments show that the performance of the new sensors is promising. The conclusion is drawn from the experimental results, and future work for this local positioning system is also described.

Place, publisher, year, edition, pages
2011. Vol. 60, no 8, p. 2881-2893
Keywords [en]
Acceleration measurement, gyroscopes, hydraulic systems, industrial electronics, mechanical variables measurement, position measurement, sonar distance measurement, sonar transducers
National Category
Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
URN: urn:nbn:se:miun:diva-14691DOI: 10.1109/TIM.2011.2121191ISI: 000293658600015Scopus ID: 2-s2.0-79960414914Local ID: STCOAI: oai:DiVA.org:miun-14691DiVA, id: diva2:454793
Available from: 2011-11-08 Created: 2011-11-08 Last updated: 2017-12-08Bibliographically approved
In thesis
1. Applications of embedded sensors in loader crane positioning and rotor RPM measurement
Open this publication in new window or tab >>Applications of embedded sensors in loader crane positioning and rotor RPM measurement
2011 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

In this thesis, two novel applications involving embedded sensors arestudied, one dealing with loader crane positioning and the other involving rotorRevolutions Per Minute (RPM) measurement. The thesis presents a generalintroduction to the embedded sensor, its architecture and its use in mechanicalindustry, and provides the reader with an overview of conventional sensortechnologies within the fields of angle sensors and angular speed sensors, coveringtheir working principles, features, advantages and disadvantages and typicalapplications. The particular problems associated with the use of conventionalsensors in both loader crane positioning and rotor RPM measurement aredescribed and these problems provided the motivation for the designs of theembedded sensor systems developed in this thesis.In the case of the loader crane positioning, the origins of the project and thespecial requirements of the application are described in detail. In addition, apreliminary study is conducted in relation to the idea of a contactless joint angularsensor using MEMS inertial sensors in which four different methods, namely, theCommon-Mode-Rejection with Gyro Integration (CMRGI), Common-Mode-Rejection (CMR), Common-Mode-Rejection with Gyro Differentiation (CMRGD)and Distributed Common-Mode-Rejection (DCMR), are conceived, modeled andtested on a custom-designed prototype experimental setup. The results gatheredfrom these four methods are compared and analyzed in order to identify thedifferences in their performances. The methods, which proved to be suitable, arethen further tested using the prototype sensor setup on a loader crane and theperformance results are analyzed in order to make a decision in relation to the twomost suitable methods for the application of the loader crane positioning. Theresults suggested that the two most suitable were the CMRGD and the DCMR. Thepractical design issues relating to this sensor system are highlighted andsuggestions are made in the study. Additionally, possible future work for thisproject is also covered.In the first case for the rotor RPM measurement, the thesis presents themodeling and simulation of the stator-free RPM sensor idea using the Monte Carlomethod, which demonstrated the special features and performance of this sensor.The design aspects of the prototype sensor are described in detail and theprototype is tested on an experimental setup. The conclusions for the stator-freeRPM sensor are then made from the analysis of the experimental results and futurework in relation to this sensor is also proposed.In the second case of the rotor RPM measurement, the thesis presentsanother idea involving the laser mouse RPM sensor and the main focus of thestudy is on the performance characterization of the laser mouse sensor and theverification of the RPM sensor idea. Experiments are conducted using the test setup and results are gathered and analyzed and conclusions are drawn.Possibilities in relation to future work for this laser mouse RPM sensor are alsoprovided.The summary and the conclusion form the final chapter of the thesis andseveral important aspects of the designs relating to both the loader cranepositioning project and the rotor RPM measurement project are discussed.

Place, publisher, year, edition, pages
Sundsvall: Mid Sweden University, 2011. p. 63
Series
Mid Sweden University doctoral thesis, ISSN 1652-893X ; 114
National Category
Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:miun:diva-15710 (URN)STC (Local ID)978-91-86694-56-2 (ISBN)STC (Archive number)STC (OAI)
Supervisors
Available from: 2012-01-16 Created: 2012-01-16 Last updated: 2016-10-19Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records BETA

Cheng, PengOelmann, Bengt

Search in DiVA

By author/editor
Cheng, PengOelmann, Bengt
By organisation
Department of Information Technology and Media
In the same journal
IEEE Transactions on Instrumentation and Measurement
Electrical Engineering, Electronic Engineering, Information Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 655 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf