miun.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
High Strain Rate Compression and Sliding Friction of Wood under Refining Conditions
Mid Sweden University, Faculty of Science, Technology and Media, Department of Natural Sciences. (FSCN – Fibre Science and Communication Network)ORCID iD: 0000-0003-3381-5516
Mid Sweden University, Faculty of Science, Technology and Media, Department of Engineering, Physics and Mathematics.
Mid Sweden University, Faculty of Science, Technology and Media, Department of Engineering, Physics and Mathematics. (FSCN – Fibre Science and Communication Network)
Mid Sweden University, Faculty of Science, Technology and Media, Department of Natural Sciences.
Responsible organisation
2007 (English)In: International Mechanical Pulping Conference 2007, TAPPI, 2007, Vol. 2, 983-994 p.Conference paper, (Other academic)
Abstract [en]

Compression and friction characteristics are needed in order to gain a better grasp of the forces acting during refining. To this end, both stress-strain relations and frictional behavior of wood were investigated under simulated chip refining conditions (hot saturated steam, high strain rate compression, and high sliding speed). Two new, custom-designed, experimental set-ups were used. Both pieces of equipment allow a testing environment of hot saturated steam. The wood-steel friction investigations indicate that when making measurements in the lower temperature region (100C-130C), surface properties such as lubrication have a great influence on the coefficients of friction. Traces of lubricating layers, comprising fatty acids, were found on friction-tested pine surfaces using a staining technique and light microscopy; in the higher-temperature region no traces of lubrication could be detected in this way.

Place, publisher, year, edition, pages
2007. Vol. 2, 983-994 p.
Keyword [en]
Friction, Compression
National Category
Chemical Engineering
Identifiers
URN: urn:nbn:se:miun:diva-4279Scopus ID: 2-s2.0-55849096900Local ID: 5060ISBN: 978-160560293-6 (print)OAI: oai:DiVA.org:miun-4279DiVA: diva2:29311
Conference
International Mechanical Pulping Conference 2007, TAPPI; Minneapolis, MN; United States; 6 May 2007 through 9 May 2007; Code 73991
Available from: 2008-09-30 Created: 2009-06-08 Last updated: 2016-09-23Bibliographically approved
In thesis
1. Frictional studies and high strain rate testing of wood under refining conditions
Open this publication in new window or tab >>Frictional studies and high strain rate testing of wood under refining conditions
2007 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

When producing thermomechanical pulps (TMP), wood chips and fiber material are loaded mechanically in a disc-refiner to separate the fibers and to make them flexible. In the process, much of the energy supplied is transferred to the fiber material through cyclic compression, shear and friction processes. Therefore, compression and friction characteristics are needed in order to gain a better grasp of the forces acting during refining. To this end, in this thesis, the compressive and frictional behaviors of wood were investigated under simulated chip refining conditions (i.e., hot saturated steam, high strain rate compression, and high sliding speed). Two new, custom-designed, experimental setups were developed and used. The equipment used for compression testing was based on the split Hopkinson pressure bar (SHPB) technique and the friction tester was a pin-on-disc type of tribotester (wear rig). Both pieces of equipment allow a testing environment of hot saturated steam.

 

In the wood–steel friction investigation, the influence of the steam temperature (100-170°C) was of primary interest. The wood species chosen for the friction tests were spruce (Picea abies), pine (Pinus sylvestris, Pinus radiata), and birch (Betula verrucosa). When performing measurements in the lower-temperature region (100-130°C), the friction coefficients registered for the softwoods were generally low and surface properties such as lubrica­tion were suggested to have a great influence on the results; however, in the higher-tempera­ture region (~130 -170°C), the friction coefficients of all investigated wood species were probably determined by bulk properties to a much greater extent. When most of the wood extractives had been removed from the specimens, testing results revealed distinct peaks in friction at similar temperatures, as the internal friction of the different wood species are known to have their maxima at ~110–130°C. One suggested explanation of these friction peaks is that reduced lubrication enabled energy to dissipate into the bulk material, causing particularly high friction at the temperature at which internal damping of the material was greatest. During the friction measurements in the higher-temperature region, the specimens of the different wood species also started to lose fibers (i.e., produce wear debris) at different characteristic temperatures, as indicated by peaks in the coefficient of friction. In refining, the generally lower shives content of pine TMP than of spruce TMP could partly be explained by a lower wear initiation temperature in the pine species.

 

Wood stiffness is known to decrease with temperature, when measured at low strain rates. The results presented in this thesis can confirm a similar behavior for high strain rate compression. The compressive strain registered during impulsive loading (using a modified split Hopkinson equipment) increased with temperature; because strain rate also increased with temperature. Accordingly, the strain rates should determine the strain magnitudes also in a refiner, since the impulsive loads in a refiner are of similar type. Larger strains would thus be achieved when refining at high temperatures. The results achieved in the compression tests were also considered in relation to refining parameters such as plate clearance and refining intensity, parameters that could be discussed in light of the stress–strain relations derived from the high strain rate measurements. Trials recorded using high-speed photography demonstrated that the wood relaxation was very small in the investigated time frame ~6 ms. As well, in TMP refining the wood material has little time to relax, i.e., ~0.04–0.5 ms in a large single disc refiner. The results presented here are therefore more suitable for comparison with the impulsive loads arising in a refiner than are the results of any earlier study. It can therefore be concluded that the modified SHPB testing technique combined with high-speed photography is well suited for studying the dynamic behavior of wood under conditions like those prevalent in a TMP system.

Place, publisher, year, edition, pages
Sundsvall: Mittuniversitetet, 2007. 88 p.
Series
Mid Sweden University doctoral thesis, ISSN 1652-893X ; 31
Keyword
Friction, High strain rate testing, Wood, Mechanical pulping, Tribology, Refining, Energy consumption
National Category
Chemical Engineering
Identifiers
urn:nbn:se:miun:diva-8895 (URN)978-91-85317-64-6 (ISBN)
Public defence
(English)
Supervisors
Available from: 2013-04-16 Created: 2009-05-06 Last updated: 2013-04-16Bibliographically approved

Open Access in DiVA

No full text

Scopus

Search in DiVA

By author/editor
Svensson, Birgitta A.Holmgren, Sven-ErikGradin, Per A.Höglund, Hans
By organisation
Department of Natural SciencesDepartment of Engineering, Physics and Mathematics
Chemical Engineering

Search outside of DiVA

GoogleGoogle Scholar

Total: 851 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf