Mid Sweden University

The hypothesis is that it should be possible to modify papermaking conditions in line with the softening properties of high yield pulp fibres and achieve similar strength properties to conventional chemical pulp based paper. We therefore investigated the rheological and physical properties of high yield pulp based papers during hot-pressing. Our results confirm that increased temperature combined with sufficient pressure enables permanent densification by softening of lignin, producing very high tensile strength. This treatment also significantly improved the wet tensile strength in comparison to bleached kraft pulp without using wet strength agents. The high yield pulps used here were spruce based thermomechanical pulp, chemi-thermomechanical pulp, and high temperature chemi-thermomechanical pulp, and birch-aspen based neutral sulphite semi chemical pulp, with spruce-pine based bleached kraft pulp as reference. Rapid Köhten sheets of 150g/m2 and 50 % dryness were hot-pressed in a cylinder-press at 20–200 °C, 7 MPa, and 1 m/min. The mechanical properties showed great improvements in these high yield pulp papers, with tensile index increased to 75 kNm/kg and compression strength index to 45 kNm/kg; levels close to and better than bleached kraft. Wet strength increased to 16 Nm/g compared to 5 Nm/g for bleached kraft.

It is known that the strength properties of wood-based paper materials can be enhanced via hot-pressing techniques. Today, there is a desire not only for a change from fossil-based packaging materials to new sustainable bio-based materials, but also for more effective and eco-friendly solutions for improving the dry and wet strength of paper and board. Against this background, hot pressing of paper made from high yield pulp (HYP), rich in lignin, becomes highly interesting. This study investigated the influence of pressing temperature and native lignin content on the properties of paper produced by means of hot pressing. Kraft pulps of varied lignin content (kappa numbers: 25, 50, 80) were produced at pilot scale from the same batch by varying the cooking time. We then studied the effect of lignin content by evaluating the physical properties of Rapid When sheets after hot pressing in the temperature range of 20 degrees C-200 degrees C with a constant nip pressure of 7 MPa. The pilot-scale cooked pulps were compared with reference samples of mill-produced northern bleached softwood kraft (NBSK) pulp and mill-produced chemithermomechanical pulp (CTMP). Generally, the results demonstrated that lignin content had a significant effect on both dry and wet tensile index. All of the pilot cooked pulps with increased lignin content had a higher tensile index than the reference NBSK pulp. To obtain high tensile index, both dry and wet, the pressing temperature should be set high, preferably at least 200 degrees C; that is, well above the glass transition temperature (Tg) for lignin. Moreover, the lignin content should preferably also be high. All kraft pulps investigated in this study showed a linear relationship between wet strength and lignin content.

The dry strength properties of hot-pressed moist paper improved as stiff high-yield pulp fibers soften and the sheet density increased. Very high wet strength was also achieved without adding strengthening agents. This research focuses on a new hot-pressing methodology based on a steel belt-based pilot cylinder press with infrared heating. The heated steel belt transports the moist paper into the cylinder nip with two adjacent steel rollers with adjustable nip pressure. The temperature ranges up to 300 °C, maximum speed is 5 m/min, maximum pulling force from the steel belt is 70 kN and the line load in the two press nips is 15 kN/m each. High peak pressures are possible due to the hard press nip between steel rolls and steel belt, allowing a good heat transfer to the paper. The long dwell time allows strained drying of the paper which results to high density and high wet strength. Paper samples from high-yield pulps were tested at different nip pressures, temperatures and machine speeds while the dry content was kept constant at about 63%. High nip pressure showed the largest effect on densification and dry strength. While high temperature and long dwell time seem to be most important in achieving high wet strength.

Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing temperature of 270 °C. The stronger bonding of wet fibres can be explained by the inter-diffusion of lignin macromolecules with an activation energy around 26 kJ mol−1 after lignin softening. The associated exponential acceleration of diffusion with temperature dominates over other factors such as process dynamics or final material density in setting wet strength. The optimum pressing temperature for dry strength is generally lower, around 200 °C, beyond which hemicellulose degradation begins. By varying the solids content prior to hot-pressing for the TMP sheets, the highest wet strength is achieved for the completely dry web, while no strong correlation was observed for the dry strength. 

Hot-pressing high yield pulp-based paper, well above softening temperature of lignin, increases paper density and paper strength. It has been investigated whether improved paper strength can be achieved and if lower pressing temperatures can be used in combination with increased sulfonation of HTCTMP (high temperature chemi-thermomechanical pulp).Moist paper sheets from low-energy Norway Spruce HTCTMP were hot-pressed up to 270°C. Sulfite charges from 25 to 120 kg/bdt were used during impregnation, preheating, and refining at 180°C with an electric energy demand of 370–500 kWh/bdt to a shive content of 1%. The pulps were mixed with 20% bleached unrefined kraft pulp to ensure that the sheet formation would not be hampered by the coarseness of the pulps. A tensile index of 70 kNm/kg was reached with highest sulfite dosage at only 150°C in pressing temperature which can be compared to 60 kNm/kg for the corresponding market CTMP. To obtain high wet strength, the highest temperature was required, while the sulfite charge was found to be of minor importance. This study has shown that it is possible to obtain strong and wet-stable paper products from HTCTMP, having a yield of 94-96% and a low energy demand at reduced pressing temperature.