miun.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Process window for electron beam melting of 316LN stainless steel
Mittuniversitetet, Fakulteten för naturvetenskap, teknik och medier, Institutionen för kvalitets- och maskinteknik.ORCID-id: 0000-0002-2543-2809
(Engelska)Manuskript (preprint) (Övrigt vetenskapligt)
Nationell ämneskategori
Annan maskinteknik
Identifikatorer
URN: urn:nbn:se:miun:diva-37871OAI: oai:DiVA.org:miun-37871DiVA, id: diva2:1375336
Tillgänglig från: 2019-12-04 Skapad: 2019-12-04 Senast uppdaterad: 2019-12-04Bibliografiskt granskad
Ingår i avhandling
1. Process Development for Electron Beam Melting of 316LN Stainless Steel
Öppna denna publikation i ny flik eller fönster >>Process Development for Electron Beam Melting of 316LN Stainless Steel
2019 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Additive manufacturing (AM) is a technology that inverts the procedure of traditional machining. Instead of starting with a billet of material and removing unwanted parts, the AM manufacturing process starts with an empty workspace and proceeds to fill this workspace with material where it is desired, often in a layer-by-layer fashion. Materials available for AM processing include polymers, concrete, metals, ceramics, paper, photopolymers, and resins. This thesis is concerned with electron beam melting (EBM), which is a powder bed fusion technology that uses an electron beam to selectively melt a feedstock of fine powder to form geometries based on a computer-aided design file input. There are significant differences between EBM and conventional machining. Apart from the process differences, the ability to manufacture extremely complex parts almost as easily as a square block of material gives engineers the freedom to disregard complexity as a cost-driving factor. The engineering benefits of AM also include manufacturing geometries which were previously almost impossible, such as curved internal channels and complex lattice structures. Lattices are lightweight structures comprising a network of thin beams built up by multiplication of a three-dimensional template cell, or unit cell. By altering the dimensions and type of the unit cell, one can tailor the properties of the lattice to give it the desired behavior. Lattices can be made stiff or elastic, brittle or ductile, and even anisotropic, with different properties in different directions. This thesis focuses on alleviating one of the problems with EBM and AM, namely the relatively few materials available for processing. The method is to take a closer look at the widely used stainless steel 316LN, and investigate the possibility of processing 316LN powder via the EBM process into both lattices and solid material. The results show that 316LN is suitable for EBM processing, and a processing window is presented. The results also show that some additional work is needed to optimize the process parameters for increased tensile strength if the EBM-processed material is to match the yield strength of additively laser-processed 316L material.

Ort, förlag, år, upplaga, sidor
Sundsvall: Mid Sweden University, 2019. s. 39
Serie
Mid Sweden University licentiate thesis, ISSN 1652-8948 ; 164
Nyckelord
additive manufacturing, beam deflection rate, electron beam melting, energy input, material properties, microstructure, powder bed fusion, process parameters, 316LN stainless steel
Nationell ämneskategori
Annan maskinteknik
Identifikatorer
urn:nbn:se:miun:diva-37840 (URN)978-91-88947-25-3 (ISBN)
Presentation
2019-12-18, Q221, Akademigatan 1, 831 25 Östersund, 09:00 (Svenska)
Opponent
Handledare
Forskningsfinansiär
Interreg Sverige-Norge, TROJAM3DC
Anmärkning

Vid tidpunkten för framläggningen av avhandlingen var följande delarbete opublicerat: delarbete 3 (inskickat).

At the time of the defence the following paper was unpublished: paper 3 (submitted).

Tillgänglig från: 2019-12-04 Skapad: 2019-12-03 Senast uppdaterad: 2019-12-04Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Personposter BETA

Roos, Stefan

Sök vidare i DiVA

Av författaren/redaktören
Roos, Stefan
Av organisationen
Institutionen för kvalitets- och maskinteknik
Annan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 67 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf