miun.sePublikationer
Ändra sökning
Länk till posten
Permanent länk

Direktlänk
BETA
Lidenmark, Cecilia
Alternativa namn
Publikationer (8 of 8) Visa alla publikationer
Andersson, H., Manuilskiy, A., Gao, J., Lidenmark, C., Sidén, J., Forsberg, S., . . . Nilsson, H.-E. (2014). Investigation of Humidity Sensor Effect in Silver Nanoparticle Ink Sensors Printed on Paper. IEEE Sensors Journal, 14(3), Art. no. 6615915
Öppna denna publikation i ny flik eller fönster >>Investigation of Humidity Sensor Effect in Silver Nanoparticle Ink Sensors Printed on Paper
Visa övriga...
2014 (Engelska)Ingår i: IEEE Sensors Journal, ISSN 1530-437X, E-ISSN 1558-1748, Vol. 14, nr 3, s. Art. no. 6615915-Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Thin inkjet-printed tracks of silver nanoparticles have previously been observed to show a non-reversible decrease in resistance when exposed to a high degree of relative humidity and thus providing sensor functionality with a memory effect. This paper provides a more in-depth explanation of the observed humidity sensor effect that originates from inkjet-printed silver nanoparticle sensors on a paper substrate. It is shown that the geometry of the sensor has a large effect on the sensor's initial resistance, and therefore also on the sensor's resistive dynamic range. The importance of the sensor geometry is believed to be due to the amount of solvent from the ink interacting with the coating of the paper substrate, which in turn enables the diffusion of salts from the paper coating into the ink and thus affecting the silver ink.

Nyckelord
Humidity sensor, ink jet, silver nanoparticle ink
Nationell ämneskategori
Elektroteknik och elektronik Materialteknik Nanoteknik
Identifikatorer
urn:nbn:se:miun:diva-19888 (URN)10.1109/JSEN.2013.2284033 (DOI)000331560300002 ()2-s2.0-84892379399 (Scopus ID)STC (Lokalt ID)STC (Arkivnummer)STC (OAI)
Tillgänglig från: 2013-09-19 Skapad: 2013-09-19 Senast uppdaterad: 2017-12-06Bibliografiskt granskad
Lidenmark, C., Pettersson, T., Karlsson, O. J. J., Notley, S. M., Edlund, H. & Norgren, M. (2013). The adhesive behavior of extracted Latex polymers towards Silicon oxide and Cellulose. International Journal of Adhesion and Adhesives, 44, 250-258
Öppna denna publikation i ny flik eller fönster >>The adhesive behavior of extracted Latex polymers towards Silicon oxide and Cellulose
Visa övriga...
2013 (Engelska)Ingår i: International Journal of Adhesion and Adhesives, ISSN 0143-7496, E-ISSN 1879-0127, Vol. 44, s. 250-258Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The objective with this work is to compare the adhesive behavior for latex polymers of different Glass transition Temperatures (Tg) at different length scales and with different contact times. This is accomplished by two techniques: AFM colloidal probe force measurements and JKR-measurements. The aim is to compare the results from these two techniques and relate them to the interaction of the latex polymers towards oxidized silicon wafers and silica/cellulose probes. Theory suggests that altering the short timeframes used in the colloidal probe technique does not affect the ranking of the adhesion for the different polymers, but for the macroscopic JKR-technique it influences the measured work of adhesion. It is therefore important to let the system reach a steady state before assuming complete spreading and adhesion. AFM and JKR measurements showed the same trends where the polymer with lowest content of styrene has the lowest Tg and the highest adhesion, due to the larger polymer chain mobility.

Nyckelord
latex, atomic force microscopy, adhesion, Polymer thin film
Nationell ämneskategori
Fysikalisk kemi
Identifikatorer
urn:nbn:se:miun:diva-18457 (URN)10.1016/j.ijadhadh.2013.02.017 (DOI)000320485200031 ()2-s2.0-84876560008 (Scopus ID)
Projekt
Interactions between dispersion polymers and cellulose
Tillgänglig från: 2013-02-12 Skapad: 2013-02-12 Senast uppdaterad: 2017-12-06Bibliografiskt granskad
Andersson, H., Manuilskiy, A., Lidenmark, C., Gao, J., Öhlund, T., Forsberg, S., . . . Nilsson, H.-E. (2013). The influence of paper coating content on room temperature sintering of silver nanoparticle ink. Nanotechnology, 24(45), Art. no. 455203
Öppna denna publikation i ny flik eller fönster >>The influence of paper coating content on room temperature sintering of silver nanoparticle ink
Visa övriga...
2013 (Engelska)Ingår i: Nanotechnology, ISSN 0957-4484, E-ISSN 1361-6528, Vol. 24, nr 45, s. Art. no. 455203-Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The resistance of inkjet printed lines using a silver nanoparticle based ink can be very dependent on the substrate. A very large difference in resistivity was observed for tracks printed on paper substrates with aluminum oxide based coatings compared to silica based coatings. Silica based coatings are often cationized with polymers using chloride as a counter ion. It is suggested that the precipitation of silver salts is the cause of the high resistivity, since papers pretreated with salt solutions containing ions that precipitate silver salts gave a high resistance. Silver nitrate has a high solubility and paper pretreated with nitrate ions gave a low resistivity without sintering. The results obtained show that, by choosing the correct type of paper substrate, it is possible to manufacture printed structures, such as interconnects on paper, without the need for, or at least to reduce the need for, post-print sintering. This phenomenon is, of course, ink specific. Inks without or with a low silver ion content are not expected to behave in this manner. In some sensor applications, a high resistivity is desired and, by using the correct combination of ink and paper, these types of sensors can be facilitated.

Nyckelord
nano silver particle ink, sintering, paper substrate
Nationell ämneskategori
Nanoteknik
Identifikatorer
urn:nbn:se:miun:diva-20353 (URN)10.1088/0957-4484/24/45/455203 (DOI)000326081400008 ()2-s2.0-84886301058 (Scopus ID)STC (Lokalt ID)STC (Arkivnummer)STC (OAI)
Tillgänglig från: 2013-11-27 Skapad: 2013-11-27 Senast uppdaterad: 2017-12-06Bibliografiskt granskad
Lidenmark, C. (2013). Time induced spreading and adhesion of latex polymers. (Licentiate dissertation). Sundsvall: Mid Sweden University
Öppna denna publikation i ny flik eller fönster >>Time induced spreading and adhesion of latex polymers
2013 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Ort, förlag, år, upplaga, sidor
Sundsvall: Mid Sweden University, 2013. s. 47
Serie
Mid Sweden University licentiate thesis, ISSN 1652-8948
Nationell ämneskategori
Kemiteknik
Identifikatorer
urn:nbn:se:miun:diva-20951 (URN)978-91-87103-87-2 (ISBN)
Handledare
Tillgänglig från: 2014-01-03 Skapad: 2014-01-03 Senast uppdaterad: 2014-01-03Bibliografiskt granskad
Andersson, H., Lidenmark, C., Öhlund, T., Örtegren, J., Manuilskiy, A., Forsberg, S. & Nilsson, H.-E. (2012). Evaluation of coatings applied to flexible substrates to enhance quality of ink jet printed silver nano-particle structures. IEEE Transactions on Components, Packaging, and Manufacturing Technology, Part C, 2(2), 342-348
Öppna denna publikation i ny flik eller fönster >>Evaluation of coatings applied to flexible substrates to enhance quality of ink jet printed silver nano-particle structures
Visa övriga...
2012 (Engelska)Ingår i: IEEE Transactions on Components, Packaging, and Manufacturing Technology, Part C, ISSN 1083-4400, E-ISSN 1558-1241, Vol. 2, nr 2, s. 342-348Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Different types of the commercial surface treatment InkAid have been evaluated as a surface treatment to enhance print quality of silver nano-particle ink structures printed on polyimide and polyethene substrate. Originally these coatings have been specified to be applied on substrates for graphical ink jet printing. On the coated polyimide and polyethene substrates lines of different widths have been printed using a Dimatix materials printer together with silver nano-particle ink manufactured by Advanced Nano Products. The prints have then been evaluated in terms of print quality and resistivity before and after sintering. The results show that the application of these coatings can improve the print quality considerably, making it possible to print lines with a good definition, which is not  otherwise possible with this type of ink on this substrate types. It has been found that the coating Semi Gloss provides the best results, both in terms of print quality as well as the lowest resistivity. The resistivity on polyethene is 3.5*10-7Ωm at best when sintered at 150°C and for polyimide  8.9*10-8Ωm sintered at 200°C. This corresponds to a conductivity of about  4.5% and  18%of bulk silver, respectively. It can be concluded that applying such PVP based coatings to polyethene and polyimide will increase the print quality quite substantially, making it possible to print patterns with requirements of smaller line widths and more details than what is possible without coating.

Nyckelord
Flexible Printed Circuits, Nanoparticles, Conductive ink
Nationell ämneskategori
Nanoteknik
Identifikatorer
urn:nbn:se:miun:diva-15019 (URN)10.1109/TCPMT.2011.2176125 (DOI)000300196600019 ()2-s2.0-84859037507 (Scopus ID)STC (Lokalt ID)STC (Arkivnummer)STC (OAI)
Tillgänglig från: 2011-12-02 Skapad: 2011-12-02 Senast uppdaterad: 2017-12-08Bibliografiskt granskad
Andersson, H., Manuilskiy, A., Unander, T., Lidenmark, C., Forsberg, S. & Nilsson, H.-E. (2012). Inkjet printed silver nanoparticle humidity sensor with memory effect on paper. IEEE Sensors Journal, 12(6), 1901-1905
Öppna denna publikation i ny flik eller fönster >>Inkjet printed silver nanoparticle humidity sensor with memory effect on paper
Visa övriga...
2012 (Engelska)Ingår i: IEEE Sensors Journal, ISSN 1530-437X, E-ISSN 1558-1748, Vol. 12, nr 6, s. 1901-1905Artikel i tidskrift (Övrigt vetenskapligt) Published
Abstract [en]

In this paper, the design and the manufacture of an inkjet printed resistive type humidity sensor on paper are reported. After having been exposed to humidity above a given threshold level, the resistance of the sensor decreases substantially and remains at that level even when thehumidity is reduced. It is possible to deduce the humidity level by monitoring the resistance. The main benefit of the printed sensor presented in this case is in relation to its very low production costs. It has also been shown that both the ink type and this paper combination used prove to be crucial in order to obtain the desired sensor effect. More research is required in order to fully understand the humidity sintering effect on the nano particle ink and the role of the substrate. However, the observed effect can be put to use in printed humidity sensors which possess a memoryfunction. The sensor can be used in various applications for environmental monitoring, for example, in situations where a large number of inexpensive and disposable humidity sensors are required which are able to detect whether they have been subjected to high humidity. This could be the checking of transportation conditions of goods or monitoring humidity within buildings. © 2001-2012 IEEE.

Nyckelord
Humidity transducers; inkjet printing; nanoparticles; sintering
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
urn:nbn:se:miun:diva-14305 (URN)10.1109/JSEN.2011.2182044 (DOI)000303400500016 ()2-s2.0-84860505067 (Scopus ID)STC (Lokalt ID)STC (Arkivnummer)STC (OAI)
Tillgänglig från: 2011-08-15 Skapad: 2011-08-15 Senast uppdaterad: 2017-12-08Bibliografiskt granskad
Lidenmark, C., Forsberg, S., Norgren, M., Edlund, H. & Karlsson, O. (2010). Changes with aging in the surface hydrophobicity of coated paper. TAPPI Journal, 9(5), 40-46
Öppna denna publikation i ny flik eller fönster >>Changes with aging in the surface hydrophobicity of coated paper
Visa övriga...
2010 (Engelska)Ingår i: TAPPI Journal, ISSN 0734-1415, Vol. 9, nr 5, s. 40-46Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Time-dependent changes in the surface properties of coated papers were studied as the evolution of surface hydrophobicity of laboratory and commercially coated papers. We measured the apparent contact angles on the papers during several weeks post-production. Hydrophobicity upon aging increased for all samples made from traditional coating colors on mechanical base stock and on base stock made from cotton linters. Accelerated aging by heat treatment intensified the increase of the apparent contact angles and accelerated the time-dependent behavior. A key mechanism in these changes may be the spreading of latex particles in a coating.

Nationell ämneskategori
Kemiteknik
Identifikatorer
urn:nbn:se:miun:diva-11838 (URN)000278601200004 ()2-s2.0-78650116607 (Scopus ID)
Tillgänglig från: 2010-07-14 Skapad: 2010-07-14 Senast uppdaterad: 2017-12-12Bibliografiskt granskad
Engqvist, C., Forsberg, S., Norgren, M., Edlund, H., Andreasson, B. & Karlsson, O. (2007). Interactions between single latex particles and silica surfaces studied with AFM. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 302(1-3), 197-203
Öppna denna publikation i ny flik eller fönster >>Interactions between single latex particles and silica surfaces studied with AFM
Visa övriga...
2007 (Engelska)Ingår i: Colloids and Surfaces A: Physicochemical and Engineering Aspects, ISSN 0927-7757, E-ISSN 1873-4359, Vol. 302, nr 1-3, s. 197-203Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The spreading of single styrene-acrylic latex particles on silicon oxide surfaces was studied using atomic force microscopy (AFM). Three latexes with different glass transition temperature (Tg) were used and the effects of temperature, time and preparation method were investigated. Particle sizes and shape were measured with AFM and the contact angles were calculated. The observed rate for the spreading of latex particles was low and it took several days before the particles reached steady state, even at temperatures well above their Tg. The experimental particle spreading results deviated with two orders of magnitude from predictions using the WLF equation for polymer diffusion. The deviation could be attributed to polymer-surface interactions that slowed down the particle spreading. The work of adhesion was calculated using two models. The results from using the regular Young-Dupré equation and a modified version of this equation that also included the mechanical properties (E-modulus and Poisson�s ratio) of the latexes, were compared. For soft latex particles the results from the two models agreed well and were of the order of 75 J/m2, but for glassy latexes the Young-Dupré equation underestimated the work of adhesion.

Nyckelord
Adhesion, AFM, latex, contact angle, surface interaction
Nationell ämneskategori
Kemi
Identifikatorer
urn:nbn:se:miun:diva-3924 (URN)10.1016/j.colsurfa.2007.02.032 (DOI)000247192300029 ()2-s2.0-34248178443 (Scopus ID)4303 (Lokalt ID)4303 (Arkivnummer)4303 (OAI)
Anmärkning

VR-Chemistry

Tillgänglig från: 2008-09-30 Skapad: 2009-11-02 Senast uppdaterad: 2017-12-12Bibliografiskt granskad
Organisationer

Sök vidare i DiVA

Visa alla publikationer